Lighting Installation Melbourne

From swapping out old halogen downlights to designing the lighting layout for a full renovation, Bitz Electrical handles lighting installation across Melbourne’s north east. We work with LED, smart and outdoor lighting systems, and every installation is carried out by a licensed A-grade electrician.

Consistent 5-Star Google Rating

Consistent 5-Star Google Rating

Consistent 5-Star Google Rating

Consistent 5-Star Google Rating

Lighting Solutions For Homes & Businesses

LED Downlight Installation & Replacement

Replacing old halogen downlights with LED, or installing downlights into new locations. We confirm dimmer compatibility and ceiling clearance before anything goes in.

Pendant & Feature Lighting

Pendants over kitchen islands and dining tables, and feature lighting in entries and living spaces. We check the ceiling fixing can support the weight before installation.

Outdoor & Garden Lighting

Weatherproof fittings for paths, decks and gardens, sensor floods for entries and driveways, all installed with the IP ratings and RCD protection outdoor circuits require.

Security & Sensor Lighting

Motion-activated lighting for entries, driveways and side access, positioned to cover the areas that matter and avoid false triggers from passing traffic.

Smart Lighting

Switch-based smart control or smart globes, with guidance on which approach suits your home and which systems are worth the investment without locking you into one ecosystem.

Bathroom Heat, Light & Fan Units

Combined heat, light and exhaust fan units installed or replaced, with the switching and ventilation requirements for bathrooms covered as part of the job.

Still running halogen downlights?

Old halogen fittings run hot, draw more power, and the transformers are usually the first thing to fail. We can convert your existing layout to LED in most cases.


Get a Quote


call:1300215193

Halogen to LED Conversion

Most homes built or fitted out through the 1990s and 2000s have halogen downlights, and by now those fittings are well past their useful life. Halogen globes draw significantly more power than LED for the same light output, and they run hot enough to be a genuine fire risk where insulation has been pushed too close to the fitting. The transformers that step down the voltage for these fittings are usually the first component to fail, and once one starts going, the rest tend to follow within a year or two.

Converting to LED removes the transformer altogether in most cases, since LED downlights run directly off mains voltage. The fittings run cool, draw a fraction of the power, and last considerably longer. If your home has dimmers, these often need to be replaced as part of the conversion, since older dimmers are built for the higher load of halogen and do not work correctly with LED, causing flickering or a limited dimming range. We check this as part of any quote so there are no surprises once the new downlights are in.

Lighting for Renovations and New Builds

Lighting layout is one of the easier things to get wrong in a renovation, because it has to be locked in before the ceiling goes up, well before you can stand in the finished room and see how it actually feels. We work through layout at the framing stage, positioning downlights, pendants and feature lighting around how each room will actually be used, not just on a grid.

This is also the point to plan for dimming, zoning, and any smart lighting control, since running the right cabling now is far simpler than retrofitting later. If you are working with a builder or designer, we can coordinate directly with them on timing and layout. For the full scope of an electrical fit-out during a renovation or new build, see our renovations and new builds page.

How We Work

Contact Us

Call 1300 215 193 or send a message with what you have in mind, whether that is a full layout or a straightforward downlight upgrade.

Assessment & Written Quote

We assess camera placement, cabling routes and storage needs, then provide a written quote before any work begins. No variations on the day.

Installation

Fittings are installed or replaced cleanly, with dimmers and switching upgraded where needed and old units removed.

Test and Certify

Everything is tested before we leave, and you receive a Certificate of Electrical Safety for all prescribed work.

Planning a renovation or new build?

Lighting layout needs to be locked in before the ceiling goes up. Talk to us early and we will plan it around how each room will actually be used.


Get a Quote


Call: 1300 215 193

Ready to Get Started?

Tell us about your property and what you want to keep an eye on, and we will recommend a system that fits, with a written quote before anything begins. Most enquiries hear back from us the same day.

Call 1300 215 193or send us a message.


Frequently Asked Questions

How many downlights do I need in a room?


It depends on the room size, ceiling height, and what the space is used for. As a general guide, downlights are spaced roughly 1.2 to 1.5 metres apart and from walls, but task areas like kitchen benches often need additional fittings. We work this out as part of the quote based on the actual room.

Yes, this is one of the most common jobs we do. In most cases the old transformers come out entirely, since LED downlights run directly off mains voltage. If your home has dimmers, we check whether they need replacing at the same time.

Often, yes. Older dimmers are built for the higher load of halogen and do not work correctly with LED, which can cause flickering, buzzing, or a limited dimming range. We confirm dimmer compatibility before installing new downlights and replace them where needed.

Warm white (around 2700 to 3000 Kelvin) gives a softer, yellow-toned light suited to living areas and bedrooms. Cool white (4000 Kelvin and above) is brighter and more blue-toned, often used in kitchens, bathrooms and garages. We can talk through what suits each room when we quote.

In many cases, yes. Smart switches can replace existing wall switches without major rewiring, and smart globes work with the existing wiring as is. Whole-home smart lighting systems generally need more planning, particularly during a renovation when walls are open.

Outdoor circuits need RCD protection and appropriately rated, weatherproof fittings and connections. Whether they sit on a dedicated circuit depends on your switchboard and existing circuits, which we assess as part of the quote.

Quality LED downlights are typically rated for 25,000 to 50,000 hours, which works out to many years of normal household use. They also run much cooler than halogen, which reduces the fire risk associated with downlights sitting close to ceiling insulation.

Yes. A Certificate of Electrical Safety is issued for all prescribed electrical work, including lighting installation and circuit alterations, as required in Victoria.

It depends on the room size, ceiling height, and what the space is used for. As a general guide, downlights are spaced roughly 1.2 to 1.5 metres apart and from walls, but task areas like kitchen benches often need additional fittings. We work this out as part of the quote based on the actual room.

Yes, this is one of the most common jobs we do. In most cases the old transformers come out entirely, since LED downlights run directly off mains voltage. If your home has dimmers, we check whether they need replacing at the same time.

Often, yes. Older dimmers are built for the higher load of halogen and do not work correctly with LED, which can cause flickering, buzzing, or a limited dimming range. We confirm dimmer compatibility before installing new downlights and replace them where needed.

Warm white (around 2700 to 3000 Kelvin) gives a softer, yellow-toned light suited to living areas and bedrooms. Cool white (4000 Kelvin and above) is brighter and more blue-toned, often used in kitchens, bathrooms and garages. We can talk through what suits each room when we quote.

In many cases, yes. Smart switches can replace existing wall switches without major rewiring, and smart globes work with the existing wiring as is. Whole-home smart lighting systems generally need more planning, particularly during a renovation when walls are open.

Outdoor circuits need RCD protection and appropriately rated, weatherproof fittings and connections. Whether they sit on a dedicated circuit depends on your switchboard and existing circuits, which we assess as part of the quote.

Quality LED downlights are typically rated for 25,000 to 50,000 hours, which works out to many years of normal household use. They also run much cooler than halogen, which reduces the fire risk associated with downlights sitting close to ceiling insulation.

Yes. A Certificate of Electrical Safety is issued for all prescribed electrical work, including lighting installation and circuit alterations, as required in Victoria.

Scroll to Top